2015+ (VA)

"You know cars, right?" I'm sure that's a question that all of us gearheads have been asked before. It's typically the wind up for a pitch to help them find the car that's going to suit every one of their specific needs, which usually looks something like a combination of reliable, fun, and gets good gas mileage. Oh yeah and it snows like once a year so all-wheel-drive is a must. Their budget is around $30k. I know what you're thinking, a 2013 BMW 328i xDrive hits the nail on the head, but I know most of us would point this friend to the obvious choice"the WRX.

Since 1992, the Subaru has made a name for itself by mixing these characteristics into the affordable WRX. Granted, we didn't see this trim until 2000, but it's no surprise why it immediately took off and became a staple in the enthusiast community.

Life is all about balance. It may be cliché, but it's true, especially when modifying cars. Attention must be paid to balancing power with handling, air with fuel, and most importantly, parts on your car with money in your wallet. That same balancing act applies to our catch can kits. We spend a lot of time balancing the cost of a catch can kit with its benefits.

Our 2016+ Camaro 2.0T catch can kit utilizes two cans to capture the maximum amount of blowby.

Many engines have a "clean" side of the crankcase ventilation system and a "dirty" side. Some engines produce just as much worrisome blow-by from their clean side as their dirty side. We usually develop a two-can kit for these engines, one for each side

Putting together our final prototype was a bit easier for this project compared to other front-mount intercooler (FMIC) kits our team has developed. As mentioned in previous segments, we used the crash beam and intercooler from our 2015 WRX kit. Now we've worked up some functional prototype piping for a final test fit.

First, let's take a quick look at each portion of the kit.

Intercooler and Crash Beam

The intercooler core is the key component in any intercooler kit. This core has provided significant air temperature drops during our testing on the WRX, and we expect the same results with the STi.

Mishimoto STi intercooler and crash beam

With our cold-side piping complete, it was time to focus on the hot side. This portion of the piping system would require a bit more attention, mainly because we were unable to scavenge any existing pipes from our WRX/STI front-mount intercooler kits (as we did with the cold side). Let's get to it!

Piping Fabrication

The hot-side piping will route from the turbocharger compressor outlet, around the driver side of the engine bay, and into the front bumper area to attach to the intercooler.

Here is a look at the turbocharger connection point.

2015 STi front-mount intercooler hot-side pipe turbo connection

A coupler attaches the pipe to the turbocharger.

Our first segment of this STI intercooler project involved the test fitting of our WRX crash beam and intercooler core. We were able to verify fitment of both pieces, which allowed our team to move on to piping fabrication. We are starting this kit with the cold-side pipe, which we've decided to place this on the passenger side of the engine bay to reduce the piping length as much as possible. Following this strategy should help reduce lag seen by the driver.

Pipe Fabrication

The cold-side pipe is a great place to start because we are able to use a portion of one of our existing kits. Because the 2015 model shares the EJ from the 2008+, we will be reusing the pipe that attaches to the throttle body and incorporates the BPV (bypass valve).

" width="300" height="180">

We're back with another quick update on our TGV delete project for the 2015+ WRX. After designing our initial models and then 3D-printing a prototype for test fitting, we worked up a couple functional prototypes for on-car testing.

First Prototype Images

Check out a few images of our functional prototype deletes!

Mishimoto's 2015 WRX TGV delete prototypes

Mishimoto's 2015 WRX TGV delete

3D-Printed Prototypes

To confirm the dimensions and design of our prototype, we decided to utilize some of our rapid prototyping tools. We fired up our 3D printer and loaded the model. Check out a couple images showing the progress of the print.

3D-printing 2015 WRX parts

3D-printing 2015 WRX parts

Once the printing process was complete, we cleaned up the prototypes and installed them on our 2015 WRX to verify fitment.