BLOG CATEGORIES

Subaru WRX Catch Can Kit 2015-2016

  1. Balancing Act - Mishimoto's 2015-16 WRX PCV Side Catch Can Kit

    Balancing Act - Mishimoto's 2015-16 WRX PCV Side Catch Can Kit

    Life is all about balance. It may be cliché, but it's true, especially when modifying cars. Attention must be paid to balancing power with handling, air with fuel, and most importantly, parts on your car with money in your wallet. That same balancing act applies to our catch can kits. We spend a lot of time balancing the cost of a catch can kit with its benefits.

    MMBCC-CAM4-16K_Install_004
    Our 2016+ Camaro 2.0T catch can kit utilizes two cans to capture the maximum amount of blowby.

    Many engines have a "clean" side of the crankcase ventilation system and a "dirty" side. Some engines produce just as much worrisome blow-by from their clean side as their dirty side. We usually develop a two-can kit for these engines, one for each side

    Continue Reading »
  2. Mishimoto 2015 Subaru WRX Direct-Fit Baffled Oil Catch Can System, Part 3: Final Product Reveal

    Mishimoto 2015 Subaru WRX Direct-Fit Baffled Oil Catch Can System, Part 3: Final Product Reveal

    Interested in purchasing our WRX catch can kit? Check out more details on our product page linked below!

    Subaru WRX Baffled Oil Catch Can System

    The final kit is ready for installation! After months of development and test fitting, we finally had our completed prototype components ready for fitment verification prior to mass production. Check out all of the components below!

    First, the passenger side catch can bracket for the PCV system.

    Final PCV catch can bracket
    Final PCV catch can bracket

    Next up is the finished version of our dual port catch can!

    Continue Reading »
  3. Mishimoto 2015 Subaru WRX Direct-Fit Baffled Oil Catch Can System, Part 2: Product Prototyping

    Mishimoto 2015 Subaru WRX Direct-Fit Baffled Oil Catch Can System, Part 2: Product Prototyping

    Interested in purchasing our WRX catch can kit? Check out more details on our product page linked below!

    Subaru WRX Baffled Oil Catch Can System

    Time to start designing brackets! After a quick recap of the project goals, our creative engineering team began brainstorming. First, they selected a location for the catch can on the PCV valve side. It would need body mounting points for the can bracket, and preferably a short route for the hose so as not to complicate the engine bay. Our goal is a clean installation that appears stock-like, not a medusa of hoses routed about the engine bay.

    The PCV valve on the 2015 WRX is located under the intercooler toward the rear of the engine block. You can see it in the image below, taken during a later stage of development of this kit.

    Continue Reading »
  4. Mishimoto 2015 Subaru WRX Direct-Fit Baffled Oil Catch Can System, Part 1: Product Introduction

    Mishimoto 2015 Subaru WRX Direct-Fit Baffled Oil Catch Can System, Part 1: Product Introduction

    Interested in purchasing our WRX catch can kit? Check out more details on our product page linked below!

    Subaru WRX Baffled Oil Catch Can System

    If you follow our engineering blog or are involved with any of our social media outlets, you should be well aware of the new baffled oil catch can we recently released. This new product features a much smaller footprint compared to our existing catch can, allowing for fitment in tighter engine bays.

    While developing this catch can, we wondered about using it in direct-fit kits for popular vehicles. For most drivers, a catch can is a DIY project requiring only the routing of hoses and fabrication of brackets for mounting the can. Installing a DIY setup that appears like it was made for the vehicle can be quite a challenge. This is where we come in, to take the guesswork out of a catch can installation. We are planning to provide mounting brackets, hardware,

    Continue Reading »